# Volume flow: litres per minute, cubic metres per hour, GPM and CFM

> Convert volume per time without confusing it with fluid speed or mass flow.

- Tool: [Volumetric flow rate Converter](https://toolsg.com/en/volumetric-flow-rate-converter)
- Language: en (available: en, zh, ms, ta)
- Last verified against official sources: 2026-10-18
- Source site: ToolSG — a planning guide, not official or financial advice. Cite the agencies listed under Sources.

## Key figures at a glance

| Fact | Value | Source |
| --- | --- | --- |
| Litre per second | 1 L/s = 0.001 m³/s | [NIST](https://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9) |
| Cubic metre per hour | 1 m³/h = 1/3600 m³/s | [NIST](https://www.nist.gov/pml/special-publication-811/nist-guide-si-chapter-5-units-outside-si) |
| US gallon per minute | 1 GPM (US) ≈ 0.0630902 L/s | [NIST](https://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9) |

## Choose both parts of the unit

Select the original flow unit and the desired unit, then enter the rate. The browser shows equivalent rates to six significant digits. Changing L/min to m³/h requires converting volume and time together, not just changing the volume label.

## GPM means US liquid gallons here

This tool's GPM uses US liquid gallons, not imperial gallons. CFM means cubic feet per minute. A flow rate is a volume over time, not a pipe velocity. Finding velocity also requires the flow area; finding mass flow requires density.

## Worked examples

Examples use the configured factors and actual engine; ≈ marks rounded results.

| Input | Result |
| --- | --- |
| 10 L/min | 0.6 m³/h |
| 100 CFM | ≈ 169.901 m³/h |
| 5 GPM | ≈ 18.9271 L/min |

## Keep the measurement conditions

Gas volume depends on conditions. Standard and actual CFM are not interchangeable by a unit factor alone; this tool does not apply pressure or temperature corrections. It also does not predict pump output or pressure loss. For a fixed quantity use the [volume converter](https://toolsg.com/en/volume-converter); for pressure units use the [pressure converter](https://toolsg.com/en/pressure-converter).

## Frequently asked questions

**How accurate are the results?**

Conversions use exact factors where an exact factor exists, and standard published values otherwise. Results are shown to six significant digits, which is more precision than almost any practical measurement warrants.

**Is anything sent to a server?**

No. The conversion runs entirely in your browser. Nothing you type is uploaded, logged or stored.

**Why does the table skip some units?**

A unit is omitted when the conversion has no finite result. In the pace converter, zero speed has no finite pace and zero pace has no finite speed.

**Can I convert several units at once?**

Yes. The table under the converter shows your value in every unit of this dimension simultaneously, so you can read off whichever you need.


## Sources

- [NIST — Gas Flowmeter Calibration and Reference Conditions](https://nvlpubs.nist.gov/nistpubs/legacy/sp/nistspecialpublication250-80.pdf)
- [NIST — Unit Conversion Factors](https://www.nist.gov/pml/special-publication-811/nist-guide-si-appendix-b-conversion-factors/nist-guide-si-appendix-b9)
- [NIST — Time Units](https://www.nist.gov/pml/special-publication-811/nist-guide-si-chapter-5-units-outside-si)
