Electric current Converter
Convert between Electric current units instantly, with every unit shown side by side.
The same value in every unit
Conversion reference
One Ampere expressed in each of the other Electric current units.
| Unit | Symbol | Equivalent |
|---|---|---|
| Milliampere | mA | 1000 |
| Microampere | µA | 1000000 |
| Kiloampere | kA | 0.001 |
In-depth guide
Electric current units: amperes, milliamps and kiloamps, and how to convert them
What the ampere measures, when to use µA, mA, A or kA, the conversion factors, worked examples (including a 230 V Singapore socket) and the mistakes that cause 1000-times errors.
Key figures at a glance
- Milliampere
- 1 mA = 0.001 A
- So 1 A = 1,000 mA. Used for electronics, chargers and battery specifications.
- Kiloampere
- 1 kA = 1,000 A
- Used for fault-current ratings and heavy industrial supplies.
- Microampere
- 1 µA = 0.000001 A
- Sensor, leakage and standby currents.
What electric current is
Electric current is the rate at which electric charge flows past a point. One ampere (A) is one coulomb of charge per second. The ampere is one of the seven SI base units, and every other electrical unit (volt, watt, ohm and so on) is built on it. All the prefixed units here are plain powers of 1,000, so the conversion is a single multiplication.
Which unit to use
| Unit | Symbol | Typical use |
|---|---|---|
| Microampere | µA | Sensor outputs, leakage and standby currents |
| Milliampere | mA | LEDs, phone chargers, battery drain, device datasheets |
| Ampere | A | Appliances, plugs, sockets and circuit breakers |
| Kiloampere | kA | Fault-current and short-circuit ratings, large industrial supplies |
In Singapore, a household meter is single-phase and marked 230 V, 50 Hz (see the SP Group guide below), so an appliance's current follows from its power: current = power ÷ voltage. This holds exactly only for a resistive load; for motors and electronics divide by the power factor as well.
The conversion
Multiply by the factor of the unit you have, then divide by the factor of the unit you want. The factors come straight from the table the converter uses: 1 mA = 0.001 A, 1 µA = 0.000001 A, 1 kA = 1,000 A.
| You have | Convert to | Result |
|---|---|---|
| 2.5 A | mA | 2,500 mA |
| 500 mA | A | 0.5 A |
| 350 µA | mA | 0.35 mA |
| 10 kA | A | 10,000 A |
| 2,000 W kettle on 230 V | A | about 8.70 A (2000 ÷ 230) |
| 1,500 W load on 230 V | A | about 6.52 A (1500 ÷ 230) |
Tip: the last two rows are approximations for resistive loads. A kettle element is nearly resistive; an air-conditioner compressor is not, so its current is higher than power ÷ voltage suggests.
Common mistakes
- Off by 1,000. A charger rated 2 A delivers up to 2,000 mA, not 2 mA. Check whether a spec says mA or A.
- Mixing up mA and mAh. Milliamps are a current (a rate). Milliamp-hours are a charge (a stored amount). To convert battery capacity use the charge converter.
- Confusing amps with watts or VA. Amps tell you how much current flows; watts depend on the voltage too. See the power converter and apparent power converter.
- Peak versus RMS. AC current ratings are normally RMS values. The peak of a sine wave is about 1.414 times larger.
- Writing "ma". A lower-case m means milli; capital M would mean mega. Current rarely uses mega, but the habit causes errors in other units.
Related tools
- Voltage converter — volts, millivolts and kilovolts.
- Power converter — watts, kW, hp and BTU/h.
- Charge converter — coulombs, Ah and mAh.
- Apparent power converter — VA and kVA.
Frequently asked questions
How accurate are the results?
Conversions use exact factors where an exact factor exists, and standard published values otherwise. Results are shown to six significant digits, which is more precision than almost any practical measurement warrants.
Is anything sent to a server?
No. The conversion runs entirely in your browser. Nothing you type is uploaded, logged or stored.
Why does the table skip some units?
A unit is omitted when the conversion has no finite result. In the pace converter, zero speed has no finite pace and zero pace has no finite speed.
Can I convert several units at once?
Yes. The table under the converter shows your value in every unit of this dimension simultaneously, so you can read off whichever you need.
Sources
- BIPM — The International System of Units (SI Brochure, 9th edition) — The ampere as an SI base unit and the SI prefixes.
- SP Group — Residential Utilities Guide — Its sample household meter is marked 230 V, 50 Hz.
This guide explains published rules in plain language. It is not financial, legal or official advice — rules change, so confirm with the agency linked above before you commit.